私はルータopenwrtに設定し、指定されたルータから取得したプロバイダのVOIP設定を使用して電話をかけようとしました。私のネットワーク設定は次のとおりです。
config interface 'loopback'
option device 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fdd2:a40d:d919::/48'
config device 'wan_dsl0_dev'
option name 'dsl0'
option macaddr XX:XX:XX:XX:XX:XX
config atm-bridge 'atm'
option vpi '1'
option vci '32'
option encaps 'llc'
option payload 'bridged'
option nameprefix 'dsl'
config dsl 'dsl'
option annex 'b'
option ds_snr_offset '0'
option line_mode 'vdsl'
option tone 'auto'
option firmware '/lib/firmware/vr9-B-dsl.bin'
config device
option name 'br-lan'
option type 'bridge'
list ports 'lan1'
list ports 'lan2'
list ports 'lan3'
list ports 'lan4'
config interface 'lan'
option device 'br-lan'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
config interface 'wan'
option device 'dsl0.835'
option proto 'pppoe'
option username 'username'
option password 'password'
option ipv6 'none'
option keepalive '10'
option mtu '1492'
list dns '1.1.1.1'
option peerdns '0'
config interface voip
option device 'dsl0.837'
option proto 'dhcp'
config interface 'wan6'
option device '@wan'
option proto 'dhcpv6'
ご覧のとおり、voipはvlanを使用していますdsl0.837
。また、次のようにsiproxyを設定しました。
config siproxd general
# Custom options allow using OpenWRT network names, and defaults should
# work out-of-the-box. If your SIP devices do not REGISTER externally,
# you may also need to open firewall ports: tcp/udp 5060, udp 7070-7089.
option interface_inbound lan
# option interface_outbound dsl0.837
# All other documented siproxd configuration directives are supported. Use
# a UCI 'option' for single-instance directives, and UCI 'list' entries for
# directives that allow multiple instances, per the examples below.
# Define low-level network devices, overriding interface_in/outbound:
# option if_inbound eth0
option if_outbound dsl0.837
# Enable DEBUG logging for configuration messages:
# option debug_level 0x00000100
# option silence_log 0
# Load two plugins: one that logs SIP call details to syslog, and one
# that strips out G.729, GSM codecs:
# list load_plugin 'plugin_logcall.so'
# list load_plugin 'plugin_codecfilter.so'
# list plugin_codecfilter_blacklist G729
# list plugin_codecfilter_blacklist GSM
daemonize 1
masked_host=ngn.hol.net
outbound_proxy_host = ngn.hol.net
outbound_proxy_port = 5060
その後、イーサネットを介してLANに接続されたマイコンピュータでは、ekigaは次のように設定されます。
ただし、VoIPに正常に接続されたにもかかわらず、まだ携帯電話に電話をかけることはできません(私のサービスプロバイダはSIP / VOIPを介して有線電話を提供します)。私のサービスプロバイダはギリシャのVodafoneです。
(ルーターのIP)に電話をかけましたがsip:^my_cellphone_number^@192.168.1.1
できませんでした。なぜそれを知っていますか?
私のファイアウォール設定も次のとおりです。
config defaults
option syn_flood 1
option input ACCEPT
option output ACCEPT
option forward REJECT
# Uncomment this line to disable ipv6 rules
# option disable_ipv6 1
config zone
option name lan
list network 'lan'
option input ACCEPT
option output ACCEPT
option forward ACCEPT
config zone
option name wan
list network 'wan'
list network 'wan6'
option input REJECT
option output ACCEPT
option forward REJECT
option masq 1
option mtu_fix 1
config forwarding
option src lan
option dest wan
# We need to accept udp packets on port 68,
# see https://dev.openwrt.org/ticket/4108
config rule
option name Allow-DHCP-Renew
option src wan
option proto udp
option dest_port 68
option target ACCEPT
option family ipv4
# Allow IPv4 ping
config rule
option name Allow-Ping
option src wan
option proto icmp
option icmp_type echo-request
option family ipv4
option target ACCEPT
config rule
option name Allow-IGMP
option src wan
option proto igmp
option family ipv4
option target ACCEPT
config rule
option name Allow-VOIP
option src lan
option proto udp
option src_port 5060
option family ipv4
option target ACCEPT
config rule
option name Allow-VOIP
option src lan
option proto udp
option src_port 7070-7080
option family ipv4
option target ACCEPT
# Allow DHCPv6 replies
# see https://dev.openwrt.org/ticket/10381
config rule
option name Allow-DHCPv6
option src wan
option proto udp
option src_ip fc00::/6
option dest_ip fc00::/6
option dest_port 546
option family ipv6
option target ACCEPT
config rule
option name Allow-MLD
option src wan
option proto icmp
option src_ip fe80::/10
list icmp_type '130/0'
list icmp_type '131/0'
list icmp_type '132/0'
list icmp_type '143/0'
option family ipv6
option target ACCEPT
# Allow essential incoming IPv6 ICMP traffic
config rule
option name Allow-ICMPv6-Input
option src wan
option proto icmp
list icmp_type echo-request
list icmp_type echo-reply
list icmp_type destination-unreachable
list icmp_type packet-too-big
list icmp_type time-exceeded
list icmp_type bad-header
list icmp_type unknown-header-type
list icmp_type router-solicitation
list icmp_type neighbour-solicitation
list icmp_type router-advertisement
list icmp_type neighbour-advertisement
option limit 1000/sec
option family ipv6
option target ACCEPT
# Allow essential forwarded IPv6 ICMP traffic
config rule
option name Allow-ICMPv6-Forward
option src wan
option dest *
option proto icmp
list icmp_type echo-request
list icmp_type echo-reply
list icmp_type destination-unreachable
list icmp_type packet-too-big
list icmp_type time-exceeded
list icmp_type bad-header
list icmp_type unknown-header-type
option limit 1000/sec
option family ipv6
option target ACCEPT
config rule
option name Allow-IPSec-ESP
option src wan
option dest lan
option proto esp
option target ACCEPT
config rule
option name Allow-ISAKMP
option src wan
option dest lan
option dest_port 500
option proto udp
option target ACCEPT
# allow interoperability with traceroute classic
# note that traceroute uses a fixed port range, and depends on getting
# back ICMP Unreachables. if we're operating in DROP mode, it won't
# work so we explicitly REJECT packets on these ports.
config rule
option name Support-UDP-Traceroute
option src wan
option dest_port 33434:33689
option proto udp
option family ipv4
option target REJECT
option enabled false
追加のポートを開く必要がありますか?