このエラーがあります。
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Loading d0 kernel from boot module @ 0000000018000000
(XEN) Allocating 1:1 mappings totalling 1024MB for dom0:
(XEN) BANK[0] 0x00000020000000-0x00000060000000 (1024MB)
(XEN) Grant table range: 0x00000000200000-0x00000000240000
(XEN) Failed to add /axi/dma-controller@fd500000 to the IOMMU
(XEN) Device tree generation failed (-22).
(XEN)
(XEN) ****************************************
(XEN) Panic on CPU 0:
(XEN) Could not set up DOM0 guest OS
(XEN) ****************************************
xen/drivers/passthrough/device_tree.c
私のxenでphandleをお探しですかdma-controller@fd500000
? Phandleはdtcによって自動的に生成されるようですが、どのように機能するのかわかりません。私は#stream-id-cells = <1>;
成功せずに追加しようとしました。
/*
* According to the Documentation/devicetree/bindings/iommu/iommu.txt
* from Linux.
*/
while ( !dt_parse_phandle_with_args(np, "iommus", "#iommu-cells",
index, &iommu_spec) )
{
私のDTBファイル:
#include <dt-bindings/dma/xlnx-zynqmp-dpdma.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/power/xlnx-zynqmp-power.h>
#include <dt-bindings/reset/xlnx-zynqmp-resets.h>
/ {
compatible = "xlnx,zynqmp";
#address-cells = <2>;
#size-cells = <2>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "arm,cortex-a53";
device_type = "cpu";
enable-method = "psci";
operating-points-v2 = <&cpu_opp_table>;
reg = <0x0>;
cpu-idle-states = <&CPU_SLEEP_0>;
next-level-cache = <&L2>;
};
cpu1: cpu@1 {
compatible = "arm,cortex-a53";
device_type = "cpu";
enable-method = "psci";
reg = <0x1>;
operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP_0>;
next-level-cache = <&L2>;
};
cpu2: cpu@2 {
compatible = "arm,cortex-a53";
device_type = "cpu";
enable-method = "psci";
reg = <0x2>;
operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP_0>;
next-level-cache = <&L2>;
};
cpu3: cpu@3 {
compatible = "arm,cortex-a53";
device_type = "cpu";
enable-method = "psci";
reg = <0x3>;
operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP_0>;
next-level-cache = <&L2>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
};
idle-states {
entry-method = "psci";
CPU_SLEEP_0: cpu-sleep-0 {
compatible = "arm,idle-state";
arm,psci-suspend-param = <0x40000000>;
local-timer-stop;
entry-latency-us = <300>;
exit-latency-us = <600>;
min-residency-us = <10000>;
};
};
};
cpu_opp_table: opp-table-cpu {
compatible = "operating-points-v2";
opp-shared;
opp00 {
opp-hz = /bits/ 64 <1199999988>;
opp-microvolt = <1000000>;
clock-latency-ns = <500000>;
};
opp01 {
opp-hz = /bits/ 64 <599999994>;
opp-microvolt = <1000000>;
clock-latency-ns = <500000>;
};
opp02 {
opp-hz = /bits/ 64 <399999996>;
opp-microvolt = <1000000>;
clock-latency-ns = <500000>;
};
opp03 {
opp-hz = /bits/ 64 <299999997>;
opp-microvolt = <1000000>;
clock-latency-ns = <500000>;
};
};
zynqmp_ipi: zynqmp_ipi {
u-boot,dm-pre-reloc;
compatible = "xlnx,zynqmp-ipi-mailbox";
interrupt-parent = <&gic>;
interrupts = <0 35 4>;
xlnx,ipi-id = <0>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
ipi_mailbox_pmu1: mailbox@ff9905c0 {
u-boot,dm-pre-reloc;
reg = <0x0 0xff9905c0 0x0 0x20>,
<0x0 0xff9905e0 0x0 0x20>,
<0x0 0xff990e80 0x0 0x20>,
<0x0 0xff990ea0 0x0 0x20>;
reg-names = "local_request_region",
"local_response_region",
"remote_request_region",
"remote_response_region";
#mbox-cells = <1>;
xlnx,ipi-id = <4>;
};
};
dcc: dcc {
compatible = "arm,dcc";
status = "disabled";
u-boot,dm-pre-reloc;
};
pmu {
compatible = "arm,armv8-pmuv3";
interrupt-parent = <&gic>;
interrupts = <0 143 4>,
<0 144 4>,
<0 145 4>,
<0 146 4>;
interrupt-affinity = <&cpu0>,
<&cpu1>;
};
psci {
compatible = "arm,psci-0.2";
method = "smc";
};
firmware {
zynqmp_firmware: zynqmp-firmware {
compatible = "xlnx,zynqmp-firmware";
#power-domain-cells = <1>;
method = "smc";
u-boot,dm-pre-reloc;
zynqmp_power: zynqmp-power {
u-boot,dm-pre-reloc;
compatible = "xlnx,zynqmp-power";
interrupt-parent = <&gic>;
interrupts = <0 35 4>;
mboxes = <&ipi_mailbox_pmu1 0>, <&ipi_mailbox_pmu1 1>;
mbox-names = "tx", "rx";
};
nvmem_firmware {
compatible = "xlnx,zynqmp-nvmem-fw";
#address-cells = <1>;
#size-cells = <1>;
soc_revision: soc_revision@0 {
reg = <0x0 0x4>;
};
/* efuse access */
efuse_dna: efuse_dna@c {
reg = <0xc 0xc>;
};
efuse_usr0: efuse_usr0@20 {
reg = <0x20 0x4>;
};
efuse_usr1: efuse_usr1@24 {
reg = <0x24 0x4>;
};
efuse_usr2: efuse_usr2@28 {
reg = <0x28 0x4>;
};
efuse_usr3: efuse_usr3@2c {
reg = <0x2c 0x4>;
};
efuse_usr4: efuse_usr4@30 {
reg = <0x30 0x4>;
};
efuse_usr5: efuse_usr5@34 {
reg = <0x34 0x4>;
};
efuse_usr6: efuse_usr6@38 {
reg = <0x38 0x4>;
};
efuse_usr7: efuse_usr7@3c {
reg = <0x3c 0x4>;
};
efuse_miscusr: efuse_miscusr@40 {
reg = <0x40 0x4>;
};
efuse_chash: efuse_chash@50 {
reg = <0x50 0x4>;
};
efuse_pufmisc: efuse_pufmisc@54 {
reg = <0x54 0x4>;
};
efuse_sec: efuse_sec@58 {
reg = <0x58 0x4>;
};
efuse_spkid: efuse_spkid@5c {
reg = <0x5c 0x4>;
};
efuse_ppk0hash: efuse_ppk0hash@a0 {
reg = <0xa0 0x30>;
};
efuse_ppk1hash: efuse_ppk1hash@d0 {
reg = <0xd0 0x30>;
};
};
zynqmp_pcap: pcap {
compatible = "xlnx,zynqmp-pcap-fpga";
clock-names = "ref_clk";
};
zynqmp_reset: reset-controller {
compatible = "xlnx,zynqmp-reset";
#reset-cells = <1>;
};
pinctrl0: pinctrl {
compatible = "xlnx,zynqmp-pinctrl";
status = "disabled";
};
modepin_gpio: gpio {
compatible = "xlnx,zynqmp-gpio-modepin";
gpio-controller;
#gpio-cells = <2>;
};
};
};
timer {
compatible = "arm,armv8-timer";
interrupt-parent = <&gic>;
interrupts = <1 13 0xf08>,
<1 14 0xf08>,
<1 11 0xf08>,
<1 10 0xf08>;
};
edac {
compatible = "arm,cortex-a53-edac";
};
fpga_full: fpga-full {
compatible = "fpga-region";
fpga-mgr = <&zynqmp_pcap>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
};
amba: axi {
compatible = "simple-bus";
u-boot,dm-pre-reloc;
#address-cells = <2>;
#size-cells = <2>;
ranges;
can0: can@ff060000 {
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clock-names = "can_clk", "pclk";
reg = <0x0 0xff060000 0x0 0x1000>;
interrupts = <0 23 4>;
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
power-domains = <&zynqmp_firmware PD_CAN_0>;
};
can1: can@ff070000 {
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clock-names = "can_clk", "pclk";
reg = <0x0 0xff070000 0x0 0x1000>;
interrupts = <0 24 4>;
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
power-domains = <&zynqmp_firmware PD_CAN_1>;
};
cci: cci@fd6e0000 {
compatible = "arm,cci-400";
status = "disabled";
reg = <0x0 0xfd6e0000 0x0 0x9000>;
ranges = <0x0 0x0 0xfd6e0000 0x10000>;
#address-cells = <1>;
#size-cells = <1>;
pmu@9000 {
compatible = "arm,cci-400-pmu,r1";
reg = <0x9000 0x5000>;
interrupt-parent = <&gic>;
interrupts = <0 123 4>,
<0 123 4>,
<0 123 4>,
<0 123 4>,
<0 123 4>;
};
};
/* GDMA */
fpd_dma_chan1: dma-controller@fd500000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd500000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 124 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <0x01>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14e8>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan2: dma-controller@fd510000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd510000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 125 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14e9>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan3: dma-controller@fd520000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd520000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 126 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14ea>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan4: dma-controller@fd530000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd530000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 127 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14eb>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan5: dma-controller@fd540000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd540000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 128 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14ec>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan6: dma-controller@fd550000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd550000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 129 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14ed>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan7: dma-controller@fd560000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd560000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 130 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14ee>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan8: dma-controller@fd570000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xfd570000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 131 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
#stream-id-cells = <1>;
xlnx,bus-width = <128>;
iommus = <&smmu 0x14ef>;
power-domains = <&zynqmp_firmware PD_GDMA>;
};
gic: interrupt-controller@f9010000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
reg = <0x0 0xf9010000 0x0 0x10000>,
<0x0 0xf9020000 0x0 0x20000>,
<0x0 0xf9040000 0x0 0x20000>,
<0x0 0xf9060000 0x0 0x20000>;
interrupt-controller;
interrupt-parent = <&gic>;
interrupts = <1 9 0xf04>;
};
gpu: gpu@fd4b0000 {
status = "disabled";
compatible = "xlnx,zynqmp-mali", "arm,mali-400";
reg = <0x0 0xfd4b0000 0x0 0x10000>;
interrupt-parent = <&gic>;
interrupts = <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>;
interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pp1", "ppmmu1";
clock-names = "bus", "core";
power-domains = <&zynqmp_firmware PD_GPU>;
};
/* LPDDMA default allows only secured access. inorder to enable
* These dma channels, Users should ensure that these dma
* Channels are allowed for non secure access.
*/
lpd_dma_chan1: dma-controller@ffa80000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffa80000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 77 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x868>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan2: dma-controller@ffa90000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffa90000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 78 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x869>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan3: dma-controller@ffaa0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffaa0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 79 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86a>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan4: dma-controller@ffab0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffab0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 80 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86b>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan5: dma-controller@ffac0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffac0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 81 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86c>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan6: dma-controller@ffad0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffad0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 82 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86d>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan7: dma-controller@ffae0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffae0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 83 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86e>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan8: dma-controller@ffaf0000 {
status = "disabled";
compatible = "xlnx,zynqmp-dma-1.0";
reg = <0x0 0xffaf0000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 84 4>;
clock-names = "clk_main", "clk_apb";
#dma-cells = <1>;
xlnx,bus-width = <64>;
/* iommus = <&smmu 0x86f>; */
power-domains = <&zynqmp_firmware PD_ADMA>;
};
mc: memory-controller@fd070000 {
compatible = "xlnx,zynqmp-ddrc-2.40a";
reg = <0x0 0xfd070000 0x0 0x30000>;
interrupt-parent = <&gic>;
interrupts = <0 112 4>;
};
nand0: nand-controller@ff100000 {
compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10";
status = "disabled";
reg = <0x0 0xff100000 0x0 0x1000>;
clock-names = "controller", "bus";
interrupt-parent = <&gic>;
interrupts = <0 14 4>;
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x872>;
power-domains = <&zynqmp_firmware PD_NAND>;
};
gem0: ethernet@ff0b0000 {
compatible = "xlnx,zynqmp-gem", "cdns,gem";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 57 4>, <0 57 4>;
reg = <0x0 0xff0b0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x874>;
power-domains = <&zynqmp_firmware PD_ETH_0>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>;
reset-names = "gem0_rst";
};
gem1: ethernet@ff0c0000 {
compatible = "xlnx,zynqmp-gem", "cdns,gem";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 59 4>, <0 59 4>;
reg = <0x0 0xff0c0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x875>;
power-domains = <&zynqmp_firmware PD_ETH_1>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>;
reset-names = "gem1_rst";
};
gem2: ethernet@ff0d0000 {
compatible = "xlnx,zynqmp-gem", "cdns,gem";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 61 4>, <0 61 4>;
reg = <0x0 0xff0d0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x876>;
power-domains = <&zynqmp_firmware PD_ETH_2>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>;
reset-names = "gem2_rst";
};
gem3: ethernet@ff0e0000 {
compatible = "xlnx,zynqmp-gem", "cdns,gem";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 63 4>, <0 63 4>;
reg = <0x0 0xff0e0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x877>;
power-domains = <&zynqmp_firmware PD_ETH_3>;
resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>;
reset-names = "gem3_rst";
};
gpio: gpio@ff0a0000 {
compatible = "xlnx,zynqmp-gpio-1.0";
status = "disabled";
#gpio-cells = <0x2>;
gpio-controller;
interrupt-parent = <&gic>;
interrupts = <0 16 4>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x0 0xff0a0000 0x0 0x1000>;
power-domains = <&zynqmp_firmware PD_GPIO>;
};
i2c0: i2c@ff020000 {
compatible = "cdns,i2c-r1p14";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 17 4>;
reg = <0x0 0xff020000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&zynqmp_firmware PD_I2C_0>;
};
i2c1: i2c@ff030000 {
compatible = "cdns,i2c-r1p14";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 18 4>;
reg = <0x0 0xff030000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&zynqmp_firmware PD_I2C_1>;
};
ocm: memory-controller@ff960000 {
compatible = "xlnx,zynqmp-ocmc-1.0";
reg = <0x0 0xff960000 0x0 0x1000>;
interrupt-parent = <&gic>;
interrupts = <0 10 4>;
};
qspi: spi@ff0f0000 {
u-boot,dm-pre-reloc;
compatible = "xlnx,zynqmp-qspi-1.0";
status = "disabled";
clock-names = "ref_clk", "pclk";
interrupts = <0 15 4>;
interrupt-parent = <&gic>;
num-cs = <1>;
reg = <0x0 0xff0f0000 0x0 0x1000>,
<0x0 0xc0000000 0x0 0x8000000>;
#address-cells = <1>;
#size-cells = <0>;
iommus = <&smmu 0x873>;
power-domains = <&zynqmp_firmware PD_QSPI>;
};
psgtr: phy@fd400000 {
compatible = "xlnx,zynqmp-psgtr-v1.1";
status = "disabled";
reg = <0x0 0xfd400000 0x0 0x40000>,
<0x0 0xfd3d0000 0x0 0x1000>;
reg-names = "serdes", "siou";
#phy-cells = <4>;
};
rtc: rtc@ffa60000 {
compatible = "xlnx,zynqmp-rtc";
status = "disabled";
reg = <0x0 0xffa60000 0x0 0x100>;
interrupt-parent = <&gic>;
interrupts = <0 26 4>, <0 27 4>;
interrupt-names = "alarm", "sec";
calibration = <0x7FFF>;
};
sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
status = "disabled";
reg = <0x0 0xfd0c0000 0x0 0x2000>;
interrupt-parent = <&gic>;
interrupts = <0 133 4>;
power-domains = <&zynqmp_firmware PD_SATA>;
resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
/* iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, */
/* <&smmu 0x4c2>, <&smmu 0x4c3>; */
/* dma-coherent; */
};
sdhci0: mmc@ff160000 {
u-boot,dm-pre-reloc;
compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 48 4>;
reg = <0x0 0xff160000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
iommus = <&smmu 0x870>;
#clock-cells = <1>;
clock-output-names = "clk_out_sd0", "clk_in_sd0";
power-domains = <&zynqmp_firmware PD_SD_0>;
resets = <&zynqmp_reset ZYNQMP_RESET_SDIO0>;
};
sdhci1: mmc@ff170000 {
u-boot,dm-pre-reloc;
compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 49 4>;
reg = <0x0 0xff170000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
iommus = <&smmu 0x871>;
#clock-cells = <1>;
clock-output-names = "clk_out_sd1", "clk_in_sd1";
power-domains = <&zynqmp_firmware PD_SD_1>;
resets = <&zynqmp_reset ZYNQMP_RESET_SDIO1>;
};
smmu: iommu@fd800000 {
compatible = "arm,mmu-500";
reg = <0x0 0xfd800000 0x0 0x20000>;
#iommu-cells = <1>;
status = "okay";
#global-interrupts = <1>;
interrupt-parent = <&gic>;
interrupts = <0 155 4>,
<0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
<0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
<0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
<0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>;
};
watchdog0: watchdog@fd4d0000 {
compatible = "cdns,wdt-r1p2";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 113 1>;
reg = <0x0 0xfd4d0000 0x0 0x1000>;
timeout-sec = <60>;
reset-on-timeout;
};
lpd_watchdog: watchdog@ff150000 {
compatible = "cdns,wdt-r1p2";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 52 1>;
reg = <0x0 0xff150000 0x0 0x1000>;
timeout-sec = <10>;
};
xilinx_ams: ams@ffa50000 {
compatible = "xlnx,zynqmp-ams";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 56 4>;
interrupt-names = "ams-irq";
reg = <0x0 0xffa50000 0x0 0x800>;
reg-names = "ams-base";
#address-cells = <1>;
#size-cells = <1>;
#io-channel-cells = <1>;
ranges = <0 0 0xffa50800 0x800>;
ams_ps: ams_ps@0 {
compatible = "xlnx,zynqmp-ams-ps";
status = "disabled";
reg = <0x0 0x400>;
};
ams_pl: ams_pl@400 {
compatible = "xlnx,zynqmp-ams-pl";
status = "disabled";
reg = <0x400 0x400>;
};
};
zynqmp_dpdma: dma-controller@fd4c0000 {
compatible = "xlnx,zynqmp-dpdma";
status = "disabled";
reg = <0x0 0xfd4c0000 0x0 0x1000>;
interrupts = <0 122 4>;
interrupt-parent = <&gic>;
clock-names = "axi_clk";
power-domains = <&zynqmp_firmware PD_DP>;
dma-channels = <6>;
iommus = <&smmu 0xce4>;
#dma-cells = <1>;
};
zynqmp_dpaud_setting: dp_aud@fd4ac000 {
compatible = "xlnx,zynqmp-dpaud-setting", "syscon";
reg = <0x0 0xfd4ac000 0x0 0x1000>;
};
};
};
そして:
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include "pl.dtsi"
#include "pcw.dtsi"
/ {
chosen {
bootargs = "earlycon clk_ignore_unused";
stdout-path = "serial0:115200n8";
#address-cells = <0x02>;
#size-cells = <0x01>;
xen,xen-bootargs = "console=dtuart dtuart=serial0 dom0_mem=1G bootscrub=0 maxcpus=1 timer_slop=0";
xen,dom0-bootargs = "console=hvc0 earlycon=xen maxcpus=1 earlyprintk=xen clk_ignore_unused root=/dev/mmcblk0p2 rootwait quiet";
dom0 {
compatible = "xen,linux-zimage", "xen,multiboot-module";
reg = <0x0 0x00080000 0x3100000>;
};
};
aliases {
ethernet0 = &gem2;
i2c0 = &i2c0;
i2c1 = &i2c1;
serial0 = &uart0;
serial1 = &uart1;
spi0 = &qspi;
spi1 = &spi0;
spi2 = &spi1;
};
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x7ff00000>;
};
cpus {
/delete-node/ cpu@2 ;
/delete-node/ cpu@3 ;
};
};
&sdhci0 {
non-removable;
disable-wp;
status = "okay";
};
&sdhci1 {
status = "disabled";
};
&smmu {
status = "okay";
};
&xilinx_ams {
status = "okay";
};
&ams_ps {
status = "okay";
};
&ams_pl {
status = "okay";
};