Debian はオールインワンコンピュータでフルモニタを使用しません

Debian はオールインワンコンピュータでフルモニタを使用しません

私は長年にわたって所有してきた古いSony VAIO VGC-JS110JでDebianとWindows 7をダブルブートしました。私はLinuxに初めて触れたので、私に話してください。私はLXDEと無料のファームウェアを含む安定したamd64バージョンを使用することにしました。

一度完全にインストールされたら、私は逃げましたapt-get updateapt-get upgrade完全に起動してログインすると、ディスプレイ解像度は1600 x 1200 60 Hzですが、画面の右インチが使用されず、ディスプレイの下部が画面から少し離れています(タスクバーは表示されません)。解像度を1600x1050 59Hzに設定しましたが、画面で見える部分にぴったりのようです。

オールインワンコンピュータ

私はどこでも見ましたが、この問題を解決するものが見つからないようです。私は本当にLinuxを使用したいのですが、この問題は難しい状況にあります。 Debian が画面を最大限に活用する方法は?

追加情報:

Windows 7 64ビットは、1680 x 1050 59Hzの解像度で正しく動作します。

xrandr -q出力: (私は1600x1050_59.00を作りました)

Screen 0: minimum 320 x 200, current 1600 x 1050, maximum 8192 x 8192
LVDS-1 connected primary 1600x1050+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
   1600x1200     60.00 +
   1600x1050_59.00  59.00* 
VGA-1 connected (normal left inverted right x axis y axis)
   1024x768      60.00  
   800x600       60.32    56.25  
   848x480       60.00  
   640x480       59.94  

lshw -c video:

  *-display:0               
       description: VGA compatible controller
       product: 4 Series Chipset Integrated Graphics Controller
       vendor: Intel Corporation
       physical id: 2
       bus info: pci@0000:00:02.0
       version: 03
       width: 64 bits
       clock: 33MHz
       capabilities: msi pm vga_controller bus_master cap_list rom
       configuration: driver=i915 latency=0
       resources: irq:28 memory:fe400000-fe7fffff memory:d0000000-dfffffff ioport:ec00(size=8) memory:c0000-dffff
  *-display:1 UNCLAIMED
       description: Display controller
       product: 4 Series Chipset Integrated Graphics Controller
       vendor: Intel Corporation
       physical id: 2.1
       bus info: pci@0000:00:02.1
       version: 03
       width: 64 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list
       configuration: latency=0
       resources: memory:fe800000-fe8fffff

/var/log/Xorg.0.log:

[  1244.821] 
X.Org X Server 1.19.2
Release Date: 2017-03-02
[  1244.821] X Protocol Version 11, Revision 0
[  1244.821] Build Operating System: Linux 4.9.0-4-amd64 x86_64 Debian
[  1244.821] Current Operating System: Linux debian 4.9.0-4-amd64 #1 SMP Debian 4.9.51-1 (2017-09-28) x86_64
[  1244.821] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-4-amd64 root=UUID=f09f044d-6a4b-47c4-8da1-a0fce2ff092c ro quiet
[  1244.821] Build Date: 16 October 2017  08:19:45AM
[  1244.821] xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support) 
[  1244.821] Current version of pixman: 0.34.0
[  1244.821]    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[  1244.821] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[  1244.822] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Dec  2 11:05:27 2017
[  1244.822] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[  1244.822] (==) No Layout section.  Using the first Screen section.
[  1244.822] (==) No screen section available. Using defaults.
[  1244.822] (**) |-->Screen "Default Screen Section" (0)
[  1244.822] (**) |   |-->Monitor "<default monitor>"
[  1244.822] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[  1244.823] (==) Automatically adding devices
[  1244.823] (==) Automatically enabling devices
[  1244.823] (==) Automatically adding GPU devices
[  1244.823] (==) Max clients allowed: 256, resource mask: 0x1fffff
[  1244.823] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[  1244.823]    Entry deleted from font path.
[  1244.823] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi,
    built-ins
[  1244.823] (==) ModulePath set to "/usr/lib/xorg/modules"
[  1244.823] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[  1244.823] (II) Loader magic: 0x55bfd01b4e00
[  1244.823] (II) Module ABI versions:
[  1244.823]    X.Org ANSI C Emulation: 0.4
[  1244.823]    X.Org Video Driver: 23.0
[  1244.823]    X.Org XInput driver : 24.1
[  1244.823]    X.Org Server Extension : 10.0
[  1244.824] (++) using VT number 7

[  1244.824] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[  1244.825] (II) xfree86: Adding drm device (/dev/dri/card0)
[  1244.840] (--) PCI:*(0:0:2:0) 8086:2e22:104d:9044 rev 3, Mem @ 0xfe400000/4194304, 0xd0000000/268435456, I/O @ 0x0000ec00/8, BIOS @ 0x????????/131072
[  1244.841] (--) PCI: (0:0:2:1) 8086:2e23:104d:9044 rev 3, Mem @ 0xfe800000/1048576
[  1244.841] (II) LoadModule: "glx"
[  1244.841] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[  1244.843] (II) Module glx: vendor="X.Org Foundation"
[  1244.843]    compiled for 1.19.2, module version = 1.0.0
[  1244.843]    ABI class: X.Org Server Extension, version 10.0
[  1244.843] (==) Matched modesetting as autoconfigured driver 0
[  1244.843] (==) Matched fbdev as autoconfigured driver 1
[  1244.843] (==) Matched vesa as autoconfigured driver 2
[  1244.843] (==) Assigned the driver to the xf86ConfigLayout
[  1244.844] (II) LoadModule: "modesetting"
[  1244.844] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[  1244.844] (II) Module modesetting: vendor="X.Org Foundation"
[  1244.844]    compiled for 1.19.2, module version = 1.19.2
[  1244.844]    Module class: X.Org Video Driver
[  1244.844]    ABI class: X.Org Video Driver, version 23.0
[  1244.844] (II) LoadModule: "fbdev"
[  1244.844] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[  1244.844] (II) Module fbdev: vendor="X.Org Foundation"
[  1244.845]    compiled for 1.19.0, module version = 0.4.4
[  1244.845]    Module class: X.Org Video Driver
[  1244.845]    ABI class: X.Org Video Driver, version 23.0
[  1244.845] (II) LoadModule: "vesa"
[  1244.845] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[  1244.845] (II) Module vesa: vendor="X.Org Foundation"
[  1244.845]    compiled for 1.19.0, module version = 2.3.4
[  1244.845]    Module class: X.Org Video Driver
[  1244.845]    ABI class: X.Org Video Driver, version 23.0
[  1244.845] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[  1244.845] (II) FBDEV: driver for framebuffer: fbdev
[  1244.845] (II) VESA: driver for VESA chipsets: vesa
[  1244.855] (II) modeset(0): using drv /dev/dri/card0
[  1244.855] (WW) Falling back to old probe method for fbdev
[  1244.855] (II) Loading sub module "fbdevhw"
[  1244.855] (II) LoadModule: "fbdevhw"
[  1244.855] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[  1244.855] (II) Module fbdevhw: vendor="X.Org Foundation"
[  1244.855]    compiled for 1.19.2, module version = 0.0.2
[  1244.855]    ABI class: X.Org Video Driver, version 23.0
[  1244.855] (WW) Falling back to old probe method for vesa
[  1244.856] (II) modeset(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[  1244.856] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[  1244.856] (==) modeset(0): RGB weight 888
[  1244.856] (==) modeset(0): Default visual is TrueColor
[  1244.856] (II) Loading sub module "glamoregl"
[  1244.856] (II) LoadModule: "glamoregl"
[  1244.856] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[  1244.863] (II) Module glamoregl: vendor="X.Org Foundation"
[  1244.863]    compiled for 1.19.2, module version = 1.0.0
[  1244.863]    ABI class: X.Org ANSI C Emulation, version 0.4
[  1244.863] (II) glamor: OpenGL accelerated X.org driver based.
[  1244.880] (II) glamor: EGL version 1.4 (DRI2):
[  1244.885] (II) modeset(0): glamor initialized
[  1244.986] (II) modeset(0): Output LVDS-1 has no monitor section
[  1245.136] (II) modeset(0): Output VGA-1 has no monitor section
[  1245.234] (II) modeset(0): EDID for output LVDS-1
[  1245.234] (II) modeset(0): Printing probed modes for output LVDS-1
[  1245.234] (II) modeset(0): Modeline "1600x1200"x60.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 -hsync -vsync (75.0 kHz eP)
[  1245.388] (II) modeset(0): EDID for output VGA-1
[  1245.388] (II) modeset(0): Printing probed modes for output VGA-1
[  1245.388] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[  1245.388] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[  1245.388] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[  1245.388] (II) modeset(0): Modeline "848x480"x60.0   33.75  848 864 976 1088  480 486 494 517 +hsync +vsync (31.0 kHz e)
[  1245.388] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[  1245.388] (II) modeset(0): Output LVDS-1 connected
[  1245.388] (II) modeset(0): Output VGA-1 connected
[  1245.388] (II) modeset(0): Using sloppy heuristic for initial modes
[  1245.388] (II) modeset(0): Output LVDS-1 using initial mode 1600x1200 +0+0
[  1245.388] (II) modeset(0): Output VGA-1 using initial mode 1024x768 +0+0
[  1245.388] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[  1245.388] (==) modeset(0): DPI set to (96, 96)
[  1245.388] (II) Loading sub module "fb"
[  1245.388] (II) LoadModule: "fb"
[  1245.388] (II) Loading /usr/lib/xorg/modules/libfb.so
[  1245.389] (II) Module fb: vendor="X.Org Foundation"
[  1245.389]    compiled for 1.19.2, module version = 1.0.0
[  1245.389]    ABI class: X.Org ANSI C Emulation, version 0.4
[  1245.389] (II) UnloadModule: "fbdev"
[  1245.389] (II) Unloading fbdev
[  1245.389] (II) UnloadSubModule: "fbdevhw"
[  1245.389] (II) Unloading fbdevhw
[  1245.389] (II) UnloadModule: "vesa"
[  1245.389] (II) Unloading vesa
[  1245.389] (==) Depth 24 pixmap format is 32 bpp
[  1245.534] (==) modeset(0): Backing store enabled
[  1245.534] (==) modeset(0): Silken mouse enabled
[  1245.534] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[  1245.535] (==) modeset(0): DPMS enabled
[  1245.535] (II) modeset(0): [DRI2] Setup complete
[  1245.535] (II) modeset(0): [DRI2]   DRI driver: i965
[  1245.535] (II) modeset(0): [DRI2]   VDPAU driver: i965
[  1245.535] (--) RandR disabled
[  1245.539] (II) SELinux: Disabled on system
[  1245.548] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[  1245.548] (II) AIGLX: enabled GLX_ARB_create_context
[  1245.548] (II) AIGLX: enabled GLX_ARB_create_context_profile
[  1245.548] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[  1245.548] (II) AIGLX: enabled GLX_INTEL_swap_event
[  1245.548] (II) AIGLX: enabled GLX_SGI_swap_control
[  1245.548] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[  1245.548] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[  1245.548] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[  1245.548] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[  1245.548] (II) AIGLX: Loaded and initialized i965
[  1245.548] (II) GLX: Initialized DRI2 GL provider for screen 0
[  1245.551] (II) modeset(0): Damage tracking initialized
[  1245.551] (II) modeset(0): Setting screen physical size to 423 x 317
[  1245.612] (II) config/udev: Adding input device Power Button (/dev/input/event5)
[  1245.612] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[  1245.612] (II) LoadModule: "libinput"
[  1245.612] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[  1245.614] (II) Module libinput: vendor="X.Org Foundation"
[  1245.614]    compiled for 1.19.0, module version = 0.23.0
[  1245.614]    Module class: X.Org XInput Driver
[  1245.614]    ABI class: X.Org XInput driver, version 24.1
[  1245.614] (II) Using input driver 'libinput' for 'Power Button'
[  1245.614] (**) Power Button: always reports core events
[  1245.614] (**) Option "Device" "/dev/input/event5"
[  1245.614] (**) Option "_source" "server/udev"
[  1245.615] (II) input device 'Power Button', /dev/input/event5 is tagged by udev as: Keyboard
[  1245.615] (II) input device 'Power Button', /dev/input/event5 is a keyboard
[  1245.632] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input10/event5"
[  1245.632] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[  1245.632] (**) Option "xkb_model" "pc105"
[  1245.632] (**) Option "xkb_layout" "us"
[  1245.633] (II) input device 'Power Button', /dev/input/event5 is tagged by udev as: Keyboard
[  1245.633] (II) input device 'Power Button', /dev/input/event5 is a keyboard
[  1245.634] (II) config/udev: Adding input device Sony Vaio Keys (/dev/input/event6)
[  1245.634] (**) Sony Vaio Keys: Applying InputClass "libinput keyboard catchall"
[  1245.634] (II) Using input driver 'libinput' for 'Sony Vaio Keys'
[  1245.634] (**) Sony Vaio Keys: always reports core events
[  1245.634] (**) Option "Device" "/dev/input/event6"
[  1245.634] (**) Option "_source" "server/udev"
[  1245.635] (II) input device 'Sony Vaio Keys', /dev/input/event6 is tagged by udev as: Keyboard
[  1245.635] (II) input device 'Sony Vaio Keys', /dev/input/event6 is a keyboard
[  1245.648] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/SNY5001:00/input/input11/event6"
[  1245.648] (II) XINPUT: Adding extended input device "Sony Vaio Keys" (type: KEYBOARD, id 7)
[  1245.648] (**) Option "xkb_model" "pc105"
[  1245.648] (**) Option "xkb_layout" "us"
[  1245.648] (II) input device 'Sony Vaio Keys', /dev/input/event6 is tagged by udev as: Keyboard
[  1245.648] (II) input device 'Sony Vaio Keys', /dev/input/event6 is a keyboard
[  1245.649] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/event7)
[  1245.649] (**) Sony Vaio Jogdial: Applying InputClass "libinput keyboard catchall"
[  1245.649] (II) Using input driver 'libinput' for 'Sony Vaio Jogdial'
[  1245.649] (**) Sony Vaio Jogdial: always reports core events
[  1245.649] (**) Option "Device" "/dev/input/event7"
[  1245.649] (**) Option "_source" "server/udev"
[  1245.650] (II) input device 'Sony Vaio Jogdial', /dev/input/event7 is tagged by udev as: Keyboard
[  1245.650] (II) input device 'Sony Vaio Jogdial', /dev/input/event7 is a keyboard
[  1245.664] (II) libinput: Sony Vaio Jogdial: needs a virtual subdevice
[  1245.664] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/SNY5001:00/input/input12/event7"
[  1245.664] (II) XINPUT: Adding extended input device "Sony Vaio Jogdial" (type: MOUSE, id 8)
[  1245.664] (**) Option "AccelerationScheme" "none"
[  1245.664] (**) Sony Vaio Jogdial: (accel) selected scheme none/0
[  1245.664] (**) Sony Vaio Jogdial: (accel) acceleration factor: 2.000
[  1245.664] (**) Sony Vaio Jogdial: (accel) acceleration threshold: 4
[  1245.665] (II) input device 'Sony Vaio Jogdial', /dev/input/event7 is tagged by udev as: Keyboard
[  1245.665] (II) input device 'Sony Vaio Jogdial', /dev/input/event7 is a keyboard
[  1245.665] (II) config/udev: Adding input device Sony Vaio Jogdial (/dev/input/mouse1)
[  1245.666] (II) No input driver specified, ignoring this device.
[  1245.666] (II) This device may have been added with another device file.
[  1245.666] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[  1245.666] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[  1245.666] (II) Using input driver 'libinput' for 'Power Button'
[  1245.666] (**) Power Button: always reports core events
[  1245.666] (**) Option "Device" "/dev/input/event4"
[  1245.666] (**) Option "_source" "server/udev"
[  1245.667] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[  1245.667] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[  1245.680] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input9/event4"
[  1245.680] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 9)
[  1245.680] (**) Option "xkb_model" "pc105"
[  1245.680] (**) Option "xkb_layout" "us"
[  1245.681] (II) input device 'Power Button', /dev/input/event4 is tagged by udev as: Keyboard
[  1245.681] (II) input device 'Power Button', /dev/input/event4 is a keyboard
[  1245.682] (II) config/udev: Adding input device UVC Camera (05ca:183d) (/dev/input/event13)
[  1245.682] (**) UVC Camera (05ca:183d): Applying InputClass "libinput keyboard catchall"
[  1245.682] (II) Using input driver 'libinput' for 'UVC Camera (05ca:183d)'
[  1245.682] (**) UVC Camera (05ca:183d): always reports core events
[  1245.682] (**) Option "Device" "/dev/input/event13"
[  1245.682] (**) Option "_source" "server/udev"
[  1245.683] (II) input device 'UVC Camera (05ca:183d)', /dev/input/event13 is tagged by udev as: Keyboard
[  1245.683] (II) input device 'UVC Camera (05ca:183d)', /dev/input/event13 is a keyboard
[  1245.712] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.7/usb6/6-3/6-3:1.0/input/input18/event13"
[  1245.712] (II) XINPUT: Adding extended input device "UVC Camera (05ca:183d)" (type: KEYBOARD, id 10)
[  1245.712] (**) Option "xkb_model" "pc105"
[  1245.712] (**) Option "xkb_layout" "us"
[  1245.713] (II) input device 'UVC Camera (05ca:183d)', /dev/input/event13 is tagged by udev as: Keyboard
[  1245.713] (II) input device 'UVC Camera (05ca:183d)', /dev/input/event13 is a keyboard
[  1245.713] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event8)
[  1245.713] (II) No input driver specified, ignoring this device.
[  1245.714] (II) This device may have been added with another device file.
[  1245.714] (II) config/udev: Adding input device HDA Intel Mic (/dev/input/event9)
[  1245.714] (II) No input driver specified, ignoring this device.
[  1245.714] (II) This device may have been added with another device file.
[  1245.715] (II) config/udev: Adding input device HDA Intel Line (/dev/input/event10)
[  1245.715] (II) No input driver specified, ignoring this device.
[  1245.715] (II) This device may have been added with another device file.
[  1245.715] (II) config/udev: Adding input device HDA Intel Headphone (/dev/input/event11)
[  1245.715] (II) No input driver specified, ignoring this device.
[  1245.716] (II) This device may have been added with another device file.
[  1245.717] (II) config/udev: Adding input device Lite-On Technology Corp. USB Multimedia Keyboard (/dev/input/event0)
[  1245.717] (**) Lite-On Technology Corp. USB Multimedia Keyboard: Applying InputClass "libinput keyboard catchall"
[  1245.717] (II) Using input driver 'libinput' for 'Lite-On Technology Corp. USB Multimedia Keyboard'
[  1245.717] (**) Lite-On Technology Corp. USB Multimedia Keyboard: always reports core events
[  1245.717] (**) Option "Device" "/dev/input/event0"
[  1245.717] (**) Option "_source" "server/udev"
[  1245.718] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[  1245.718] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event0 is a keyboard
[  1245.748] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.0/0003:04CA:0050.0005/input/input5/event0"
[  1245.748] (II) XINPUT: Adding extended input device "Lite-On Technology Corp. USB Multimedia Keyboard" (type: KEYBOARD, id 11)
[  1245.748] (**) Option "xkb_model" "pc105"
[  1245.748] (**) Option "xkb_layout" "us"
[  1245.749] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[  1245.749] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event0 is a keyboard
[  1245.750] (II) config/udev: Adding input device Lite-On Technology Corp. USB Multimedia Keyboard (/dev/input/event1)
[  1245.750] (**) Lite-On Technology Corp. USB Multimedia Keyboard: Applying InputClass "libinput keyboard catchall"
[  1245.750] (II) Using input driver 'libinput' for 'Lite-On Technology Corp. USB Multimedia Keyboard'
[  1245.750] (**) Lite-On Technology Corp. USB Multimedia Keyboard: always reports core events
[  1245.750] (**) Option "Device" "/dev/input/event1"
[  1245.750] (**) Option "_source" "server/udev"
[  1245.751] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event1 is tagged by udev as: Keyboard
[  1245.751] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event1 is a keyboard
[  1245.780] (II) libinput: Lite-On Technology Corp. USB Multimedia Keyboard: needs a virtual subdevice
[  1245.780] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.1/0003:04CA:0050.0006/input/input6/event1"
[  1245.780] (II) XINPUT: Adding extended input device "Lite-On Technology Corp. USB Multimedia Keyboard" (type: MOUSE, id 12)
[  1245.780] (**) Option "AccelerationScheme" "none"
[  1245.780] (**) Lite-On Technology Corp. USB Multimedia Keyboard: (accel) selected scheme none/0
[  1245.780] (**) Lite-On Technology Corp. USB Multimedia Keyboard: (accel) acceleration factor: 2.000
[  1245.780] (**) Lite-On Technology Corp. USB Multimedia Keyboard: (accel) acceleration threshold: 4
[  1245.781] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event1 is tagged by udev as: Keyboard
[  1245.781] (II) input device 'Lite-On Technology Corp. USB Multimedia Keyboard', /dev/input/event1 is a keyboard
[  1245.782] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event2)
[  1245.782] (**) Logitech USB Receiver: Applying InputClass "libinput pointer catchall"
[  1245.782] (II) Using input driver 'libinput' for 'Logitech USB Receiver'
[  1245.782] (**) Logitech USB Receiver: always reports core events
[  1245.782] (**) Option "Device" "/dev/input/event2"
[  1245.782] (**) Option "_source" "server/udev"
[  1245.840] (II) input device 'Logitech USB Receiver', /dev/input/event2 is tagged by udev as: Mouse
[  1245.840] (II) input device 'Logitech USB Receiver', /dev/input/event2 is a pointer caps
[  1245.868] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.0/0003:046D:C537.0007/input/input7/event2"
[  1245.868] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 13)
[  1245.868] (**) Option "AccelerationScheme" "none"
[  1245.868] (**) Logitech USB Receiver: (accel) selected scheme none/0
[  1245.868] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[  1245.868] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[  1245.928] (II) input device 'Logitech USB Receiver', /dev/input/event2 is tagged by udev as: Mouse
[  1245.928] (II) input device 'Logitech USB Receiver', /dev/input/event2 is a pointer caps
[  1245.929] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[  1245.929] (II) No input driver specified, ignoring this device.
[  1245.929] (II) This device may have been added with another device file.
[  1245.930] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event3)
[  1245.931] (**) Logitech USB Receiver: Applying InputClass "libinput keyboard catchall"
[  1245.931] (II) Using input driver 'libinput' for 'Logitech USB Receiver'
[  1245.931] (**) Logitech USB Receiver: always reports core events
[  1245.931] (**) Option "Device" "/dev/input/event3"
[  1245.931] (**) Option "_source" "server/udev"
[  1245.932] (II) input device 'Logitech USB Receiver', /dev/input/event3 is tagged by udev as: Keyboard
[  1245.932] (II) input device 'Logitech USB Receiver', /dev/input/event3 is a keyboard
[  1245.968] (II) libinput: Logitech USB Receiver: needs a virtual subdevice
[  1245.968] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.1/0003:046D:C537.0008/input/input8/event3"
[  1245.968] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 14)
[  1245.968] (**) Option "AccelerationScheme" "none"
[  1245.968] (**) Logitech USB Receiver: (accel) selected scheme none/0
[  1245.968] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[  1245.968] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[  1245.969] (II) input device 'Logitech USB Receiver', /dev/input/event3 is tagged by udev as: Keyboard
[  1245.969] (II) input device 'Logitech USB Receiver', /dev/input/event3 is a keyboard
[  1245.970] (II) config/udev: Adding input device PC Speaker (/dev/input/event12)
[  1245.970] (II) No input driver specified, ignoring this device.
[  1245.970] (II) This device may have been added with another device file.
[  1246.000] (**) Sony Vaio Jogdial: Applying InputClass "libinput keyboard catchall"
[  1246.000] (II) Using input driver 'libinput' for 'Sony Vaio Jogdial'
[  1246.000] (**) Sony Vaio Jogdial: always reports core events
[  1246.001] (**) Option "Device" "/dev/input/event7"
[  1246.001] (**) Option "_source" "_driver/libinput"
[  1246.001] (II) libinput: Sony Vaio Jogdial: is a virtual subdevice
[  1246.001] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/SNY5001:00/input/input12/event7"
[  1246.001] (II) XINPUT: Adding extended input device "Sony Vaio Jogdial" (type: KEYBOARD, id 15)
[  1246.001] (**) Option "xkb_model" "pc105"
[  1246.001] (**) Option "xkb_layout" "us"
[  1246.001] (**) Lite-On Technology Corp. USB Multimedia Keyboard: Applying InputClass "libinput keyboard catchall"
[  1246.001] (II) Using input driver 'libinput' for 'Lite-On Technology Corp. USB Multimedia Keyboard'
[  1246.001] (**) Lite-On Technology Corp. USB Multimedia Keyboard: always reports core events
[  1246.001] (**) Option "Device" "/dev/input/event1"
[  1246.001] (**) Option "_source" "_driver/libinput"
[  1246.001] (II) libinput: Lite-On Technology Corp. USB Multimedia Keyboard: is a virtual subdevice
[  1246.002] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.1/0003:04CA:0050.0006/input/input6/event1"
[  1246.002] (II) XINPUT: Adding extended input device "Lite-On Technology Corp. USB Multimedia Keyboard" (type: KEYBOARD, id 16)
[  1246.002] (**) Option "xkb_model" "pc105"
[  1246.002] (**) Option "xkb_layout" "us"
[  1246.002] (**) Logitech USB Receiver: Applying InputClass "libinput keyboard catchall"
[  1246.002] (II) Using input driver 'libinput' for 'Logitech USB Receiver'
[  1246.002] (**) Logitech USB Receiver: always reports core events
[  1246.002] (**) Option "Device" "/dev/input/event3"
[  1246.002] (**) Option "_source" "_driver/libinput"
[  1246.002] (II) libinput: Logitech USB Receiver: is a virtual subdevice
[  1246.002] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb3/3-2/3-2:1.1/0003:046D:C537.0008/input/input8/event3"
[  1246.002] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 17)
[  1246.002] (**) Option "xkb_model" "pc105"
[  1246.002] (**) Option "xkb_layout" "us"
[  2105.748] (II) AIGLX: Suspending AIGLX clients for VT switch

答え1

簡単に言うと:5.xカーネルの明確な解決策が見つかったら、この答えを更新します。理想的な世界では、GRUBブートオプションの追加VAIOの欠陥を修正して一日を始めましょう。


それでも質問してくれて嬉しいですね。そのため、VAIOの1つに最新のLinuxディストリビューションをインストールしようとしている世界10人の人々のために、このコンテンツを文書化するためのスペースを設けました。 ;) これは本当に迷惑なことです。

一度は、カーネル4.x時代に以下を追加することでこれを行いましたdrm_kms_helper.edid_firmware=edid/1680x1050.bin引用する)をカーネルブートパラメータリストに追加します。 (Debian系システムではこれをGRUB_CMDLINE_LINUX_DEFAULTinに追加し/etc/grub/defaultてrootとして実行しますupdate-grub)。

今私はUbuntu Budgie 18.04と5.xカーネルを使って同じ目標を達成しようとしており、有効なブートパラメータの組み合わせを検索するために約10の異なるサイトをブックマークに追加しました。

カーネル4.x時代以降、いくつかの点が変更されました。起動オプションの実際の名前は次のようにdrm置き換えられます。drm_kms_helper返品4.15頃に紹介されたバージョンはedid_firmwareとにかく正しく動作しないようです。5月に提出されたパッチカーネル5.2に統合されますが、5.3、5.4、5.5などにマージされるかどうかはわかりません。結局のところ、Ubuntu 18.04(LTS)ベースのすべてのディストリビューションは回帰カーネルを使用し、私が知っている限り、修正はまだバックポートされていません。

関連情報