Seagate外付けハードドライブを接続して実行しようとしていますが、Manjaro 5.15.16-1
システムはそれを検出できません。リストに表示されず、/dev
表示できませんfdisk -l
。しかし、lsusbを通して見ることができます。
dmesg
ドライブを接続したときの出力です。
[ 1298.309372] usb 1-4: new high-speed USB device number 21 using xhci_hcd
[ 1298.464162] usb 1-4: New USB device found, idVendor=0bc2, idProduct=ab44, bcdDevice=48.85
[ 1298.464179] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1298.464185] usb 1-4: Product: Backup+ Hub
[ 1298.464190] usb 1-4: Manufacturer: Seagate
[ 1298.464194] usb 1-4: SerialNumber: 01CB0037B432
[ 1298.465693] hub 1-4:1.0: USB hub found
[ 1298.466048] hub 1-4:1.0: 3 ports detected
[ 1298.582970] usb 2-4: new SuperSpeed USB device number 23 using xhci_hcd
[ 1298.602988] usb 2-4: New USB device found, idVendor=0bc2, idProduct=ab45, bcdDevice=48.85
[ 1298.603011] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1298.603014] usb 2-4: Product: Backup+ Hub
[ 1298.603020] usb 2-4: Manufacturer: Seagate
[ 1298.603022] usb 2-4: SerialNumber: 01CB0037B432
[ 1298.605760] hub 2-4:1.0: USB hub found
[ 1298.606064] hub 2-4:1.0: 3 ports detected
[ 1299.539488] usb 1-4-port2: Cannot enable. Maybe the USB cable is bad?
[ 1301.095960] usb 2-4.1: new SuperSpeed USB device number 24 using xhci_hcd
[ 1301.113319] usb 2-4.1: New USB device found, idVendor=0bc2, idProduct=ab38, bcdDevice= 1.00
[ 1301.113338] usb 2-4.1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1301.113346] usb 2-4.1: Product: Backup+ Hub BK
[ 1301.113352] usb 2-4.1: Manufacturer: Seagate
[ 1301.113357] usb 2-4.1: SerialNumber: NA9QY9SY
[ 1301.120343] scsi host2: uas
[ 1301.121106] scsi 2:0:0:0: Direct-Access Seagate Backup+ Hub BK D781 PQ: 0 ANSI: 6
[ 1301.122043] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1301.122365] sd 2:0:0:0: [sda] Spinning up disk...
[ 1302.149335] .......................ready
[ 1324.443771] sd 2:0:0:0: [sda] 11721045167 512-byte logical blocks: (6.00 TB/5.46 TiB)
ドライブが分割されていません。
どんな助けでも大変感謝します!